KDS6-0.2TR

KDS6-0.2TR

220,000 (税込:242,000

  • 3-channel voltage standard(COM of 3-channel in common)]
    CH1: 0 to +6 V/200 mA
    CH2: 0 to +6 V/30 mA
    CH3: 0 to +6 V/ 30 mA
  • Remote sensing function that compensates for voltage drops at the output terminal
  • Best suited to operation tests for VCO and many other types of sensors
  • Voltage setting resolution of 100 μV (allows a different voltage to be set independently for each channel)
  • Current reading resolution of 0.1 μA* (in standard mode)
  • Ripple noise level lower than 100 μVrms, thus supporting measurements of high-sensitivity devices
  • High-resolution meter with an easy-to-view, 6-digit current display (no external ammeter needed)
  • Supports RS-232C and GPIB as standard interfaces
  • High-speed operation Current value refresh interval: 60 ms (in high-speed mode)
  • Setting/readout speed: 5 ms (reference value for GPIB)
  • Comes with a D-Sub 25 pin connector allowing for noise resistance

* 1μA resolution for the 200 mA range
*Discontinued and only available while supplies last


Login to myKIKUSUI / What is myKIKUSUI?
カート機能が動くまでの
SKU: KDS6-0.2TR

Overview

Suitable for evaluation tests of high-frequency electronic components and precision electronic circuits

KDS6-0.2TR is designed for use on production and inspection lines for high-frequency components capable of low supply current and low voltage operation that have become dominantly popular in recent years, as well as for a variety of electronic devices such as ICs, LSIs,and sensors. This product is a low-noise, highly stable DC voltage power supply with 3-channel output.

It solves problems such as!

On production and inspection lines for mobile phone VCOs and other products.

  • Three standard voltage generators are required for drive and control, which is costly. Ripple noise is common…

    Since it has three outputs, only one unit is required. Ripple noise is as low as 100 µVrms or less, so even a high-sensitivity VCO can be used with confidence.
  • Slow GPIB control response and takt time, need precision DMM for Current reading…

    A fast 5 ms GPIB and a 6-digit Ammeter with the fastest refresh time of 60 ms eliminate the need for a DMM.
  • When reassembling a line, wiring with the wrong polarity can cause line problems…

    Only one 25-pin D-Sub connector is required for connection, preventing mistakes when rewiring.

High-frequency circuits and high-gain circuits in the field of development.

  • It is difficult to design high-gain amplifiers and high-sensitivity VCOs with a general-purpose power supply, which is noisy and difficult to set the voltage precisely…

    Low ripple noise below 100 µVrms, with a voltage setting resolution of 100 µV.
  • I’m not sure I’d use an expensive DMM just to check microcurrents…

    A fast 5 ms GPIB and a 6-digit Ammeter with the fastest refresh time of 60 ms eliminate the need for a DMM.
  • I want to make it easier to take large amounts of data…

    Supports RS-232C and GPIB as standard interfaces

At ECU and mobile phone software development sites

  • It is difficult to check the operation of the programme without waiting for the hardware to be ready.

    It can also be run from a control microcontroller using RS-232C. The high resolution is also useful when dealing with bugs that occur around certain voltage values.

Specifications

Specifications

ZOOM
OutputRated output voltage & current rangeCH10 V to 6 V, 200 mA MAX
CH20 V to 6 V, 30 mA MAX
CH30 V to 6 V, 30 mA MAX
Output voltages setting range0.0000 V〜6.5000 V
Resolution of output voltage setting100μV
Accuracy of output voltage setting±(0.05 % of set + 2 mV)
Output ripple noise100 μVrms or less (10 Hz to 1 MHz)
CurrentResolution of current indicationCH110-mA rangeIn normal mode: 0.1 μA In high-speed mode: 1 μA
200-mA rangeIn normal mode: 1 μA In high-speed mode: 10 μA
CH2In normal mode: 0.1 μA In high-speed mode: 1 μA
CH3In normal mode: 0.1 μA In high-speed mode: 1 μA
Accuracy of current indication±(0.2 % of rdg + 20 digits)
Panel indicationVoltage7-segment LED: 5 digits
Current7-segment LED In normal mode: 6 digits In high-speed mode: 5 digits
Remote interfacesGPIBConforming to IEEE Std.488-1978 SH1, AH1, T6, TE0, L4, SR1, RL1, PP0, DC1, DT0, C0, E1
RS-232CConnector9-pin D-Sub terminal on rear panel
Bit rate2400, 4800, 9600, 19200, 38400 bps
Data bit8 bits
Stop bit1 bit
Parity bitNone
Flow controlProvided (XON/XOFF)
Temperature and humidity range for guaranteed specifications23 ℃ ± 5 ℃ 20% RH to 85% RH (without condensation)
Operating temperature and humidity range0 °C to 40 °C (32 °F to 104 °F) 20% RH to 85% RH (without condensation)
Storage temperature and humidity range-10 ℃ to 60 ℃ 90% RH or less (without condensation)
Line voltage range (AC 50/60 Hz)Voltage setting100 V90 V to 110 V
120 V104 V to 126 V
220 V194 V to 236 V
240 V207 V to 250 V
Power consumption40 VA or less
External dimensions (largest part)280W × 88H × 270D mm (305W × 105H × 330D mm)
Weight4 kg
SafetyCompliant with the requirements of the following standard: IEC61010-1:2001 Class I Pollution degree 2

Examples of Setting Values

Voltage setting error (no-load)

Voltage setting error (no-load)
Current measurement error (standard mode)

Current measurement error (standard mode)

About the load

Unlike general DC power supplies, this product is optimally designed as a low-noise voltage source. It is therefore not suitable for applications where loads with sudden current changes are driven. If the peak current is below the maximum current permitted for each channel, the OCP function can be used without being activated. However, a voltage fluctuation of ±0.1 V to ±0.5 V may occur for a few ms (*value for resistive loads) after a sudden current change.

Product Catalog

No downloads found!

    Operation Manuals

    No downloads found!

      Please feel free to contact us with any questions or concerns.

      Download a Product Catalog View List
      Request a Quotation Contact Us
      close

      Search