PCR-LE Series
よくあるご質問 閲覧ランキング
- 耐電圧(耐圧)試験って何ですか?
- 直流電源を接続する配電盤のブレーカ選定について教えてください。
- 検査票、試験成績書、校正証明書、トレーサビリティ証明書について教えてください。
- 電波法の高周波利用設備に該当する製品はありますか。
- VISAライブラリについて教えてください。
- ウォームアップ時間はどれくらいですか。
- 製品に電安法適用表示(PSEマーク)がありません。違法ではないですか。
- 耐電圧試験器を操作するために、必要な資格はありますか。
- PWR-01シリーズのPOWER スイッチをオンにしても動作しません。どうしたら良いでしょうか。
- 製品におけるPCB含有の有無について教えてください。
- マニュアル通りにコマンドを送っているのですが動作しません。どうしたらよいでしょうか。
- What is the input power for PCR-LE series?
- Can I perform the short interruption or volage slow-up/down tests from the panel of PCR-LE series?
- Can PCR-LE series perform the constant current (CC) mode during the DC mode?
- What is the tightening torque of the I/O terminal connecting screws in PCR-LE series?
- How do I insert the GPIB interface board into PCR-LE series?
- Why is the internal semiconductor protection (OCP) activated when turning off the output of PCR-LE series (e.g. PCR500LE) with a capacitor load connected?
- Is a three-phase output possible using three units of PCR-LE series with different output capacities?
- Can PCR-LE series be used to conduct a 10 ms short interruption test in accordance with the international standard IEC61000-4-29?
- Can PCR-LE series output a three-phase line-to-line voltage of 440 V at 60 Hz?
- I am using PCR-LE series to output 100 V between L-N. However, the voltage between L and G is measured as 30 V, and between N and G is measured as 70 V. Why are they unequal?
- How do I change the IP address settings for LAN communication in PCR-LE series?
- Can the compliance testing for the military standard MIL-STD-704, specifically section 5-2-3 and 5-2-4 related to avionics testing, be conducted using PCR-LE series and the optional SD012-PCR-LE/WE (avionics test software)?
- Can three units of PCR-LE series be used to provide a three-phase output of 20 kVA?
- I want to attach a 250V-20A plug to the end of the optional AC8-1P3M-M5C-3S (input power cord) of PCR-LE series, but why doesn’t the 8 sq crimped terminal fit the plug?
- Can two units of PCR-LE series be used to provide a single-phase three-wire output?
- Can PCR-LE series be damaged if an AC line loses power while the output is on?
- Is there any limit to the sensing cable length for PCR-LE series?
- Do I need any options to conduct a power supply fluctuation test using PCR-LE series?
- Why can’t I set the output voltage to 300 V in PCR-LE series?
- Can PCR-LE series be used with both 100 VAC and 200 VAC input voltage?
- I am conducting an IEC61000-4-29 compliance test (DC voltage variation test) using PCR-LE series with SD009-PCR-LE/WE (Power Line Disturbance Immunity Testing Software). Is it possible to conduct the test on PCR-LE series alone without a PC?
- What is the resolution of PCR-LE series ammeter?
- Can a constant voltage constant frequency (CVCF) power source with a three-phase output of 200 V at 60 Hz be used as a input power source for PCR-LE series?
- Can the output frequency of PCR-LE series be varied in steps?
- What is the combination of using PCR-LE series to output 220 V and 50 A at 50 Hz in a three-phase configuration?
- Can the output voltage and current be monitored when multiple units of PCR-LE series are used?
- Is it possible to ground either the L or N terminal of the single-phase two-wire output of PCR-LE series?
- Can PCR-LE2 series and the optional SD012-PCR-LE/WE (avionics test software) be used to simulate power line abnormalities?
- Can the output voltage and output on/off of PCR-LE series be controlled externally?
- Can PCR-LE series operate in constant current (CC) mode?
- I sent the command of “FETC:CURR?” via the programmable logic controller (PLC) to PCR-LE series, but I received no response. How can I retrieve the measured value?
- Is it possible to obtain a PDF version of the communication interface manual for PCR-LE series?
- Why cannot I connect a PC with the optional SD009-PCR-LE/WE (power line disturbance immunity testing software) to PCR-LE series via an RS232C interface?
- Can PCR-LE series be used as a substitute for an isolation transformer?
- Can I set unlimited repetitions of the loop for the sequence function on PCR-LE series?
- After configuring a single-phase three-wire output using the optional 2P05-PCR-LE (single-phase three-wire output driver) for PCR-LE series, is it necessary to adjust the phase once the power is turned on?