Frequently Asked Questions
よくあるご質問 閲覧ランキング
- 耐電圧（耐圧）試験って何ですか？
- 直流電源を接続する配電盤のブレーカ選定について教えてください。
- 検査票、試験成績書、校正証明書、トレーサビリティ証明書について教えてください。
- 電波法の高周波利用設備に該当する製品はありますか。
- VISAライブラリについて教えてください。
- ウォームアップ時間はどれくらいですか。
- 製品に電安法適用表示（PSEマーク）がありません。違法ではないですか。
- 耐電圧試験器を操作するために、必要な資格はありますか。
- PWR-01シリーズのPOWER スイッチをオンにしても動作しません。どうしたら良いでしょうか。
- 製品におけるPCB含有の有無について教えてください。
- マニュアル通りにコマンドを送っているのですが動作しません。どうしたらよいでしょうか。
- Frequently Asked Questions Search
- Where can I find dimensional and weight information for Kikusui products?
- Do you have detailed technical information on the Kikusui models?
- What is the cost of repair and calibration?
- Are there any Kikusui models that are RoHS 2 compliant?
- Which Kikusui models have CE marking?
- What Kikusui models can be repaired?
- When measuring resistance using the ANALOG OUT terminals on TOS7200, how long should I wait after starting the test?
- How do I perform the pre-test inspection for TOS5300 series?
- Can I use a generator as the AC power input for TOS5300 series?
- Can I capture voltage and current waveforms during tests with TOS5300 series?
- Why does TOS5300 series sometimes not respond when I control it via USB interface?
- Why does TOS5300 series display a Volt Error Protection error and prevent the withstanding voltage test from being performed?
- Why can’t I establish USB communication with TOS5300 series?
- Why are the test results unstable with TOS5300 series?
- Is the included software Data Acquisition for TOS5300 compatible with Windows 10?
- Why does the optional warning light unit (PL02A-TOS) stop working after I initialize TOS5300 series?
- Can the test voltage setting be adjusted with the rotary knob during withstanding voltage test with TOS5300 series?
- How can I reduce potential noise issues when using TOS5300 series?
- How do I operate the double action feature on TOS5300 series?
- How do I set up the double action feature on TOS5300 series?
- What is the accuracy of the analog and digital voltmeters used in TOS5300 series?
- How can I check the firmware version of TOS5300 series?
- What does the external SIGNAL I/O control for TOS5300 series do?
- Why does the DANGER LED light up briefly when I connect the test lead to the DUT with TOS5300 series?
- Why doesn’t the included software “Data Acquisition for TOS5300” start?
- What is the maximum output power of TOS5300 series?
- What are the short-circuit current ratings for TOS5300 series?
- Can TOS5302 automatically switch between the insulation resistance test (IR) and the withstanding voltage test?
- How do I enable the key lock feature on TOS5300 series?
- What is the voltage drop in the AC withstanding voltage test (ACW) for TOS5300 series?
- What type of grounding is used on TOS5300 series?
- Is it sufficient to plug TOS5300 series into a grounded outlet for proper grounding?
- Is a current of approximately 40 μA at 1.8 kV normal for a custom AC withstanding voltage test jig using TOS5300 Series?
- Can TOS5300 series be controlled by a PLC in which the common terminals for input and output signals have different potentials?
- How can I get the IR test result when running the automatic test (AUTO TEST: IR → ACW)? I get the ACW result only if I send the RES? command.
