There was a problem in which sometimes High-impedance / Low-impedance of "DC short interruption" was not output as configured.
Resolved issues
When "Run" was carried out several times in output ON, there was a problem in which interruption of setting become rarely longer than its configuration.
VER 1.12
2013-12-16
IEC61000-4-29
Resolved issues
There was a problem in which interval time was longer for 0.001 second than the setup time when repeating.
VER 1.11
2013-4-02
IEC61000-4-28
Resolved issues
At f1+Delta f, there was a problem in which minus value was out of range. This problem occurred only by Ver1.10.
VER 1.10
2013-5-25
IEC61000-4-28
Resolved issues
There was a problem in which a command error occurred when the value of more than 999.999 seconds was set.
VER 1.09
2012-2-17
Quick Immunity Sequencer
Resolved issues
There was a problem that runtime was insufficient in the installer. This problem occurred only by Ver1.08.
VER 1.08
2011-1-01
IEC61000-4-13
Resolved issues
We corrected a problem of effective value of the output voltage being different which was caused by the fact that we were not converting the voltage distortion factor due to the superimposed harmonics by Over swing, Sweep in frequency, Odd non multiple of 3, Odd multiple of 3 and Even harmonics.
VER 1.07
2009-11-30
IEC61000-4-13
Resolved issues
At Flat curve, there was a problem that Ver1.0.6 generated overshoots and undershoots when switching between banks.
VER 1.06
2009-11-12
IEC61000-4-13
Resolved issues
There was a problem that Level 0.80 required by Flat Curve Class 3, could not be set under the three-phase system.
Resolved issues
At Flat Curve under the three-phase system, the output waveform has been corrected from "line-to-line" peak-clip to "inter-phase" peak-clip.
VER 1.05
2009-4-08
Quick Immunity Sequencer
Resolved issues
When using in European region where "comma" is used as the decimal point, there was a problem that the error message "x.xx is not a valid float" was not correctly shown.
VER 1.04
2007-6-04
Quick Immunity Sequencer
Resolved issues
There was a problem that unwanted phase-shifting was generated when using IT01.
Resolved issues
There was a problem that unexpected "End" could be detected before sequence start after operating Send → Run.
Resolved issues
When launching at the condition of "Not use IT01", changing between "Use IT01" and "Not use IT01" caused a communication error.
Resolved issues
There was a problem that communication errors caused unwanted application's abortion.
VER 1.02
2005-5-13
Quick Immunity Sequencer
Resolved issues
There was a problem that send operation caused hang-up after switching "Use IT01" to "Not use IT01".
VER 1.00
2004-4-07
Quick Immunity Sequencer
New Feature
The first release
Please feel free to contact us with any questions or concerns.
Cookies will be used to track which website is being visited. On our website, we certify the information that can be accessed by visitors using cookies. We also track viewed information by users to understand your interest and provide you with a better content. You will be able to disable cookie itself, you may choose the way to use personal identification whenever you use service that requires authentication.
Strictly Necessary Cookies
Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.
If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.
Additional Cookies
This website uses the following additional cookies:
(List the cookies that you are using on the website here.)
Please enable Strictly Necessary Cookies first so that we can save your preferences!
Cookies will be used to track which website is being visited. On our website, we certify the information that can be accessed by visitors using cookies. We also track viewed information by users to understand your interest and provide you with a better content. You will be able to disable cookie itself, you may choose the way to use personal identification whenever you use service that requires authentication.
Strictly Necessary Cookies
Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.
If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.
Additional Cookies
This website uses the following additional cookies:
(List the cookies that you are using on the website here.)
Please enable Strictly Necessary Cookies first so that we can save your preferences!