PWR-01 Series
よくあるご質問 閲覧ランキング
- 耐電圧(耐圧)試験って何ですか?
- 直流電源を接続する配電盤のブレーカ選定について教えてください。
- 検査票、試験成績書、校正証明書、トレーサビリティ証明書について教えてください。
- 電波法の高周波利用設備に該当する製品はありますか。
- VISAライブラリについて教えてください。
- ウォームアップ時間はどれくらいですか。
- 製品に電安法適用表示(PSEマーク)がありません。違法ではないですか。
- 耐電圧試験器を操作するために、必要な資格はありますか。
- PWR-01シリーズのPOWER スイッチをオンにしても動作しません。どうしたら良いでしょうか。
- 製品におけるPCB含有の有無について教えてください。
- マニュアル通りにコマンドを送っているのですが動作しません。どうしたらよいでしょうか。
- Is it possible to monitor voltage and current while controlling multiple PWR-01 units with Wavy?
- Can PWR-01 series be controlled by a programmable logic controller (PLC)?
- Does PWR-01 series have a cover on the front-panel output terminals?
- What should I do if PWR-01 series has high output ripple under the external control?
- How do I synchronize the bleeder speed of two PWR-01 series during the master-slave parallel operation?
- Can I use the external monitoring on PWR-01 series to monitor the output voltage and current?
- Is it possible to record a data of the output voltage/current of PWR801L with a data logger?
- What should I do if PWR-01 series cannot be powered on by tuning the POWER switch on?
- What should I do if the output voltage from PWR-01 series does not quickly decrease after turning the output off?
- What should I do if the output ripple from PWR-01 series sometimes increases?
- The output ripple increased after PWR-01 series was moved to the different location. What should I do?
- What should I do if the LOCK LED lights on PWR-01 series and any panel operation is invalid?
- When I powered on PWR-01 series, the fan seemed to be blowing faster than usual. Is it possible to return it to normal?
- What should I do if I cannot remotely control PWR-01 series through the communication interface?
- What should I do if PWR-01 series does not switch to the local mode by pressing the LOCAL key?
- What should I do if the REMOTE LED lights on PWR-01 series and the panel operation is invalid?
- On PWR-01 series, the output voltage cannot be less than the undervoltage limit (UVL). What should I do?
- On PWR-01 series, the overvoltage protection (OVP) trip point cannot be less than 105% of the output voltage. What should I do?
- On PWR-01 series, the output voltage cannot be more than 95% of the overvoltage protection (OVP) trip point . What should I do?
- On PWR-01 series, the overcurrent protection (OCP) trip point cannot be less than 105% of the output current. What should I do?
- On PWR-01 series, the output current cannot be more than 95% of the overcurrent protection (OCP) trip point. What should I do?
- What should I do if no output is generated (the OUTPUT LED does not light) from PWR-01 series by pressing the OUTPUT key?
- What should I do if no output is generated (the OUTPUT LED lights in green) from PWR-01 series by pressing the OUTPUT key?
- What should I do if an IP address cannot be assigned from the DHCP server on the LAN interface to connect a PC and PWR-01 series?
- PWR-01 series shows “AL/Sd” on the panel with the red ALM LED on, regardless of the output on/off status. What should I do?
- PWR-01 series turns off the output soon after the output is turned on and shows “AL/oUP” on the panel. What should I do?
- PWR-01 series turns off the output soon after the output is turned on under the CC load condition. “AL/oCP” is shown on the panel. What should I do?
- PWR-01 series shut off the output, showing “AL/AC” on the panel with the red ALM LED on. What should I do?
- PWR-01 series turns off the output soon after the output is turned on under the CC load condition. “AL/FoCP” is shown on the panel. What should I do?