Frequently Asked Questions
よくあるご質問 閲覧ランキング
- 耐電圧（耐圧）試験って何ですか？
- 直流電源を接続する配電盤のブレーカ選定について教えてください。
- 検査票、試験成績書、校正証明書、トレーサビリティ証明書について教えてください。
- 電波法の高周波利用設備に該当する製品はありますか。
- VISAライブラリについて教えてください。
- ウォームアップ時間はどれくらいですか。
- 製品に電安法適用表示（PSEマーク）がありません。違法ではないですか。
- 耐電圧試験器を操作するために、必要な資格はありますか。
- PWR-01シリーズのPOWER スイッチをオンにしても動作しません。どうしたら良いでしょうか。
- 製品におけるPCB含有の有無について教えてください。
- マニュアル通りにコマンドを送っているのですが動作しません。どうしたらよいでしょうか。
- What is the function of the REMOTE connector on the front panel of TOS5300 series?
- How can I use both SIGNAL I/O and USB control on TOS5300 series and start the test with the SIGNAL I/O connector?
- Is there a polarity requirement when performing an insulation resistance test with TOS5302?
- How do I connect the optional high voltage test probe (HP01A-TOS or HP02A-TOS) to TOS5300 series?
- Why can’t I start a test when the READY LED lights up briefly and goes off after pressing the STOP switch on TOS5300 series ?
- What should I do when TOS5300 series shows “Calibration Protection” and cannot perform tests?
- What is DCW in TOS5300 series, and when is it used?
- For TOS5300 series, can I recall the panel memory when the system is in an interlock state under SIGNAL I/O control?
- Why does a Volt Error Protection occur during an AC (or DC) withstanding voltage test on TOS5300 series?
- How do I clear a USB Protection error on TOS5300 series?
- Why can’t I adjust the test voltage in 1 V steps on TOS5300 series?
- How can I check the current measurement when TOS5300 series passes a withstanding voltage test?
- When performing a withstanding voltage test with TOS5300 series, do I need to set a lower limit (LOWER) value?
- If TOS5302 displays a FAIL during an insulation resistance test, can I see the actual resistance measurement?
- How can I retrieve test results from TOS5300 series?
- What is the voltage rise time (Rise Time) setting on TOS5200?
- How can I control TOS5200 externally?
- Why does TOS5200 display a U-FAIL error and stop testing?
- What is the outer diameter of the test leads supplied with TOS5200?
- What is TOS5200?
- How long is the power cord that comes with TOS5200?
- Does TOS5200 have a discharge circuit to reduce the output voltage?
- For TOS5200’s withstanding voltage test, is the AC voltage measured in RMS or peak value?
- What is the resolution of the test time setting for TOS5200?
- What is the resolution of the voltage rise time setting on TOS5200?
- What is the resolution of the AC output setting on TOS5200?
- Can TOS5200 detect flashover?
- How do I perform a DC withstanding voltage test with TOS5200?
- I’m using the SIGNAL I/O connector to start and stop tests and the RS232C interface to retrieve measurement results on TOS5200. What should I do if the second test fails to start?
- I’m controlling TOS5200 via RS232C from a PLC. When using the FETC:VOLT? command to read the voltage, why do I only receive CR LF?
- How can I switch from the PASS/FAIL state to the READY state when
controlling TOS5200 via the USB interface? - When controlling TOS5200 via the SIGNAL I/O connector, should I connect unused pins to the circuit’s common terminal (COM)?
- What type of test leads should I use for TOS5200?
- Can the panel settings of TOS5200 be saved?
- After controlling TOS5200 via the SIGNAL I/O connector and changing the ENABLE signal after test completion, why does the DANGER LED briefly light up?
- Does the chassis terminal indicator of the LOW VOLTAGE terminal on TOS5200 indicate connection to the chassis?
